..:: PCSX2 Forums ::..

Could you please add support for:

USB\VID_0930&PID_0219

Thanks

Can I request support for
USB\VID_0A5C&PID_21B2

I was wondering if someone could help me out with this. It's probably something trivially easy that I've missed out. I've got the SCP drivers set up, and they work beautifully in PCSX2. Absolutely no issues on that front - everything works as it should, and it's a thing of beauty to behold.

I can't seem to get the PS3 controller working as an XBOX 360 controller in games that recognise it, though. Specifically, I can't get L2 and R2 to map to LT and RT. All the other buttons work fine. Is there something that I'm doing wrong? For example, in Lara Croft and the Guardian of Light, all the buttons work fine, except for LT and RT.

Thanks to anybody who sheds some light on this.

And more thanks to Scarlet Crush for programming these drivers. You sir, are a genius.

Hi guys, I have been following this thread and hoping to clarify something.

I am hoping to use the drivers develop to use my PS3 controllers on my PC via bluetooth for games and some emulators e.g. mame.

I am using motionjoy at the moment and would rather move to something more simple that does the job.

If any one can confirm it would be great!

Hi Scarlet, I tried to update system bthWinUsb to include my bluetooth ID's

USB\VID_0A12&PID_0001&REV_0100
USB\VID_0A12&PID_0001

However I dont think it worked as when I run the service it says "host address" disconnected

is there any way for us to easily add bluetooth devices to the list so that we dont hassle you to update?

Thanks and Great Work!

I'm not sure why I can't get the bluetooth to work. The USB connection works perfectly, but I'm unable to figure out how to pair the bluetooth. It seems like they're supposed to pair automatically, but it's not working for me. Whenever I unplug the controller, all four LEDs flash for a while before going out, and the ScpMonitor only reads as Reserved. I feel like I followed all the directions, so not sure what I'm doing wrong. If you could help, that'd be greatly appreciated!

Hi Seamus,
Is your bluetooth adaptor on the list?
if it is. I had a similar problem and had to unplug my bluetooth dongle and plug it into another USB port (make sure you plug it into usb 2.0 port)

Once I did that I saw the Server pick it up and it showed up on the monitor

I hope this helps

Is it possible to set my DS3 controller to player 2? I thought I'd do some L4D2 splitscreen but I only have one controller and the disconnect and connect trick does not work for ds3, unfortunately. I know this can be done with motioninjoy but I don't want to mess with it since I've heard so many bad things about it. Tell me, is motioninjoy the only way to go to accomplish this?

Nevermind, I prefer the motioninjoy driver only + better ds3 combo more than this. Not a single bug yet plus many customization options.

(07-09-2013, 01:51 PM)discostu Wrote: [ -> ]Hi Seamus,
Is your bluetooth adaptor on the list?
if it is. I had a similar problem and had to unplug my bluetooth dongle and plug it into another USB port (make sure you plug it into usb 2.0 port)

Once I did that I saw the Server pick it up and it showed up on the monitor

I hope this helps

Thanks for the response. I tried switching the USB port it was in, but still no luck (not sure how to tell if it's a 2.0 port. I do have "Standard Enhanced PCI to USB Host Controller" listed in my Device Manager twice). The dongle shows up as "BTH DS3 Device" in my Devices right now, and the Hardware ID has two values listed: USB\VID_0A12&PID_0001&REV_7558 & USB\VID_0A12&PID_0001. I believe I saw it on the list.