..:: PCSX2 Forums ::..

I am new here, Thank you for the application as I have been looking for the same function.
But I don't know how to use it....
I am using win 7 64-bit.
I install successfully but my d3 controller can't be detected in pc games.
I tried the SCP user in win 64 and it shows my controller is connected and the feedback is right.
I go to control panel -> PLAYSTATION® 3 Controller and it detect nothing.
Please help......

I have the DS3 working and the DS4 successfully showing in both the SCP Monitor and in the Profile Manager where I can see every button input being displayed. However, my DS4's light sensor will not stop blinking blue (it was blinking green for a little, but now stays blue). I tried going into the Service Configuration, and have Disable LED checked, but it has no effect on the DS4's blinking.

How can I get my DS4 working in games, turn off the LED, and remap the inputs?

To remap the inputs just use a PAD plug-in, like, say, Lilypad.

(05-27-2014, 03:04 PM)MenDude Wrote: [ -> ]To remap the inputs just use a PAD plug-in, like, say, Lilypad.

But how do I stop the blue light from blinking? It seems like the controller isn't being fully recognized because I can't disable that through the options and even the joysticks that are showing as synced aren't doing anything in Watch Dogs after I had it working with the DS3.

Edit: After reinstalling multiple times, UPlay finally recognized the controller. My dumb mistake just checking the Disable LED option (which doesn't seem to work) and not seeing the slider above to turn it down (which does work).

Sorry, but I don't fully understand how LilyPad works... I've downloaded it from this forum, but I just see a .dll file in the rar. How/where do I run it?

Also, every time I run the ScpServer it freezes my computer.

Hey,

I picked up another bluetooth dongle so that I could connect my wiiremotes to my computer. Unfortunately, I can't find a way to get my second dongle recognized as a bluetooth device. it just seems to be recognized as a DS3 BTH Device. I've tried uninstalling the driver and uninstalling the software through ScpDriver.exe. I'm not sure what to try next. Any help would be appreciated!

Thank you!

Ticoon, try to roll back the driver on the new device.

(05-28-2014, 02:39 PM)dink Wrote: [ -> ]Ticoon, try to roll back the driver on the new device.

That option is greyed out.

(05-28-2014, 04:20 AM)Nitruc Wrote: [ -> ]Sorry, but I don't fully understand how LilyPad works... I've downloaded it from this forum, but I just see a .dll file in the rar. How/where do I run it?

Also, every time I run the ScpServer it freezes my computer.

First off, uncompress it to a folder (EVERYTHING, really) then start up pcsx2.exe. Then a wizard guide will appear if it's your first time (if it's not, delete the "portable.ini" file and boot up PCSX2). Once you get to the plugin section (I think it's the first one), you can click on "config", then just... config! To assign something to a PS2 button, just click on the button you want to assign (they will say "Square", "Cross", etc.) and then press the button you want to do that (so, if you want to make S the circle button, click "Circle" and then the S button, it's the same in a DualShock device: Click "Circle" then press the O button in your DualShock controller! Oh and if you are using ScpDevice, check the XInput option in the General tab, it wrongly says it's only for XB360 controllers ). If you want to see if it's working properly, click on the device you are using in the General tab and click "Test Device", if you press S, the Circle button will have a 1.000 value (meaning it is fully pressed, you can change this if you go to the Pad tab, click on the Circle button bar that appeared in the left of the screen and then mess around with the Sensitivity). Do this for all buttons you want!

Here's a pic with my settings (this is if you have a DS3 and want to plug it in):
Page 1 (General Tab)


Page 2 (Controller 1/Pad 1 Tab)


And sorry for the language, but the buttons are "OK" (leaves config window and applies settings), "Cancel" (leaves the Config window without changing anything) and "Apply" (doesn't leave window but applies settings).

@Nitruc There is a seperate thread for DS4 stuff, that should solve your problems.

The controller functions properly with games like Broforce. However, when I start MortalKombat or WatchDogs it stops functioning after about ~1-10 minutes. The buttons I have pressed at that moment will stay pressed and the controller won't respond to anything anymore (even in controller options).

I have Windows 8.1 and I am using official sony DS3 controllers (with a cable, not bluetooth).

Any suggestions would be much obliged.