XInput Wrapper for DS3 and USB Dual DS2 Controller
Bluetooth Beta 1 (ScpServer-

Note : The Bluetooth Driver requires that you dedicate a Bluetooth Dongle to DS3 use. It will not be usable by other Bluetooth devices after the driver has been installed.

1. ScpDriver - UAC manifest control. (no need to right-click "Run as Administrator").
2. ScpDriver - Install log (saved to <install-dir>\ScpDriver.log).
3. ScpDriver - Removed legacy GUID check.
4. ScpMonitor - Settings serialization (Visibility and Form locations saved between runs).
5. ScpMonitor - Configuration Form (right-click Tray Icon and select Configuration) See attachment 1.
6. ScpControl - Configuration serialization (saved to <install-dir>\ScpControl.xml).
7. ScpControl - Added check to reject BTH connection if already connected via USB.
8. ScpControl - Added Quick Disconnect (press and hold L1+R1, then press and hold PS - DS3 will disconnect after 2 seconds).
9. ScpControl - Idle Disconnect timer configurable (Disabled, 1 - 30mins).
10. ScpControl - Stick Axis Flippable for XInput.
11. Bluetooth Driver - Removed REV requirements from Inf file*.
12. DS3 Driver - Added Navigation Controller support.
13. XInput Wrapper - Added PS/Guide button support for LilyPad-Scp/Pokopom.
14. LilyPad-Scp - Added PS button support.
15. Virtual Bus - code tidy up, removed unused code.

* Currently supported Bluetooth Dongle hardware ids :


(if your dongle is not listed - post your hardware id, and I will add it to the list and provide an update package)

Important - make sure your Bluetooth dongle and DS3(s) are plugged in via USB before running ScpDriver.exe. Make sure you have the latest DirectX redist installed and the latest X360 drivers available.

New Install
1. Connect your Dongle and DS3 via USB and let Windows install it's default drivers.
2. Unpack the archive.
3. Create a directory where you want the Service to run from [I used C:\Program Files\Scarlet.Crush Productions - create from an elevated command prompt]
4. Copy the contents of the ScpServer\bin to the directory you created.
5. Run ScpDriver.exe.
6. Click Install.
7. Click Exit.

Upgrade from Alpha 2
1. Close ScpMonitor.
2. Run <install dir>\ScpDriver.exe.
3. Ensure Configure Service is checked, then click Uninstall.
4. Unpack the archive.
5. Copy the contents of the ScpServer\bin to the directory you created.
6. Run ScpDriver.exe.
7. Click Install.
8. Click Exit.

Pairing a DS3 to your Bluetooth Dongle - plug in the DS3 to USB while the Service is running, the DS3 will be automatically paired if required.

Install / Trouble Shooting guide is not quite ready yet, I will post as soon as it is complete.

Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Edit : Added BTH Update - hardware ids (ScpServer-


Install Update
1. Unpack the archive.
2. Copy the contents of the ScpServer\bin to the directory you created.
3. Stop the Service [net stop "SCP DS3 Service" - from an elevated command prompt, or use Service Control Manager]
4. Run ScpDriver.exe
5. Uncheck Configure Service, then click Install.
6. Start the Service [net Start "SCP DS3 Service" - from an elevated command prompt, or use Service Control Manager]

Attached Files Thumbnail(s)

.7z   ScpServer- (Size: 6,68 KB / Downloads: 2.077)
.7z   ScpServer- (Size: 9,52 MB / Downloads: 4.536)
.7z   ScpServer- (Size: 6,68 KB / Downloads: 446)
.7z   ScpServer- (Size: 6,69 KB / Downloads: 479)
.7z   ScpServer- (Size: 6,67 KB / Downloads: 371)
.7z   ScpServer- (Size: 6,7 KB / Downloads: 451)
.7z   ScpServer- (Size: 6,71 KB / Downloads: 342)
.7z   ScpServer- (Size: 6,72 KB / Downloads: 373)
.7z   ScpServer- (Size: 6,72 KB / Downloads: 482)
.7z   ScpServer- (Size: 6,78 KB / Downloads: 326)
.7z   ScpServer- (Size: 6,8 KB / Downloads: 396)
.7z   ScpServer- (Size: 6,81 KB / Downloads: 448)
.7z   ScpServer- (Size: 6,83 KB / Downloads: 349)
.7z   ScpServer- (Size: 6,86 KB / Downloads: 3.278)

Sponsored links

Just wanted to say thank you very much for this driver. I've been searching for months for something like this, but I've steered clear of MiJ due to all the bad rap it gets, and my experience with libusb in the past was unsavory.

So far it seems to connect fine with my hardware (built in bluetooth from my ASUS P8Z68-V Pro) and performs wonderfully in PCSX2.
so simply copying this over the other contents in the directory and running the installer should be fine ?
@mikezilla2: yes, just make sure none of the executables are running first.
Great work once again Scarlet!
Thank you for your amazing work, Scarlet! Considering it's beta, it's already works flawlessly. When you release an RC version, we can finally ditch and bury that bloatware MIJ.
Please add USB\VID_13D3&PID_3304 to a list. It's a built-in module that could be found in a lot of laptops.
Thank you again and keep it up! Biggrin
I registered just say thanks for all your work on this =) Finally got to dump motion-joy. Could you add this Hardware Id. USB\VID_0930&PID_0215&REV_0001, USB\VID_0930&PID_0215
Again thanks Cool
Awesome work mate. I had been using libUSB to avoid using motion and joy, but now I have something better than either one Laugh. Using the bluetooth alpha (and soon the beta). Great work dude.

I do have a weird issue to report. Using the original drivers (not the bluetooth alpha), Dolphin locks up when first running it with your modified Xinput dll. Removing and reinserting my Asus BT-211 bluetooth dongle fixes it. The bluetooth alpha doesn't have the issue, so I don't know why that is going on. *shrug* Maybe it's nothing. Either way it's not bugging me since I'm using the bluetooth version now.
Windows 7 x64 | Core i5 3570K @ 4.7ghz | nVidia Geforce GTX 760 | 8GB (2x4GB) Crucial Ballistax DDR3-1600 ram | Asus Xonar Essence STX | Logitech G500

added your hardware ids, see Post #301
hello all, i just registered to thank you Scarlet for all your work and ask you for some advice Sad

i want to play with my ds3 via belkin bluetooth. i follow your post #301.
-downloaded the pack
-installed driver

controller tester shows pad is connected
server .. uhm shows some processing
monitor shows some adress but 4 pads disconnected
scpservice wont open: "windows service start failure - cannot start from command line or a debugger...."

i have no clue what to do now :/

indentifier of that dongle is USB\VID_0A5C&PID_21E8&REV_0112 ; USB\VID_0A5C&PID_21E8 but after installing your drivers i cant see bt hw in control panel so cant tell much more

Attached Files Thumbnail(s)

Users browsing this thread: 9 Guest(s)