XInput Wrapper for DS3 and Play.com USB Dual DS2 Controller

[Kirkor]

Scarlet.Crush, could you please reply to my question. Thanks

I am planning to buy Xbox 360 Wireless Gaming Receiver for Xbox 360 pads and I would like to ask if it wont interfere with SCP drivers for DS3 pads? Is there a limit for pads in Xbox 360 Controller Drivers?

Basically, my setup would be the following:
- three original DS3 pads connected at the same time to SCP drivers by bluetooth
- two original wireless Xbox 360 pads connected to Xbox 360 Wireless Gaming Receiver

My goal is to use all these 5 pads at the same time. Maximum for SCP drivers is four DS3 pads and maximum for X360 Wireless Receiver is also four (it would mean I could have eight pads for multiplayer), but I am not sure if there wont be any interference between each other.

Thank you for the answer.

[Jacky]

What About my prob.. i tried every thing..

[Scarlet.Crush]

@ToreDL87: ok, so everything looks good as far as the drivers are concerned. ScpUser uses the same extensions from bin\Win32\XInput1_3.dll that Pokopom and Lilypad-Scp use, so looks to be your PCSX2 configuration.

1. Download Pokopom r124.zip and PadTest (ELF).zip from KrossX's thread.
2. Extract padPokopom.dll and place in your PCSX2\Plugins directory [delete Lilypad-Scp-r5350.dll from the directory].
3. Copy bin\Win32\XInput1_3.dll to your PCSX2 directory.
4. Close ScpUser if it is running.
5. Start PCSX2 by double-clicking it's exe.
6. Configure your pad plugin to be Pokopom.
7. Extract padtest.elf and run it in PCSX2 [System -> Run ELF ...]
8. Screenshot below ...

@xavi40:
@hoeboo:

Note : The Bluetooth Driver requires that you dedicate a Bluetooth Dongle to DS3 use. It will not be usable by other Bluetooth devices after the driver has been installed.

The drivers replace the Windows Bluetooth Driver with a custom Driver. Expand the Universal Serial Bus devices node.

@hoeboo: can you re-run the test, press the PS button after each time you disconnect from USB. Zip up and post the ScpService.log.

@Kirkor: sorry I posted the response to your question to @olverine.

XInput supports 4 devices total, so you cannot have more than 4 XInput devices active.

@Jacky: do you have another USB cable you can try? When you did the pinhole reset was the controller disconnected from USB?

[Akovad]

@Akovad: BTH 4.0 is backward compatible with all previous BTH versions, so yes it should work. Can you do the following -

1. Unplug your DS3 from USB.
2. Restart the Service (or reboot your PC).
3. Plugin your DS3 to USB.
4. Wait 30 seconds.
5. Unplug your DS3 from USB.
6. Wait 30 seconds.
7. Plugin your DS3 to USB.
8. Wait 30 seconds.
9. Unplug your DS3 from USB.
10. Wait 30 seconds.
11. Zip up your ScpDriver.log and ScpService.log and post as an attachment.

Okay, here's those files.

EDIT: not sure why they weren't attached before, I did attach them. They are now.

[hoeboo]

@Scarlet.Crush

here you go

[CaptnJack]

Hey Scarlet, been a while since I checked in on the progress and all I can say is WOW! Updated to the latest version and everything works fantastic. Just a few questions (and I apologize if they've already been answered)

1. Did you ever setup a donation page?
2. Are there any plans to implement a way to change the controller number? Reason I ask is because if my controller dies while I'm playing the only way I know to set another controller as number 1 is to stop and restart the service.

[Solly]

Thanks for adding my BT support.

The Bluetooth is working perfectly. I will say that I had to check force install to get the Bluetooth to work. I'm not sure why since I am using Windows 7.

[SilverAga]

thank you for your fast answer and update! You're the best!

[Jacky]

@Jacky: do you have another USB cable you can try? When you did the pinhole reset was the controller disconnected from USB?

nope i don't have another cable
and yes it was connected from USB when i did the pinhole reset

but the problem is not with PCSX2 only
even with games that doesn't need PCSX2

its the stupid motioninjoy program i messed with Bluetooth pairing and suddenly the controller messed up..it wont press x-O-Square-r1-r2....Etc any more

[SilverAga]

nope i don't have another cable
and yes it was connected from USB when i did the pinhole reset

but the problem is not with PCSX2 only
even with games that doesn't need PCSX2

its the stupid motioninjoy program i messed with Bluetooth pairing and suddenly the controller messed up..it wont press x-O-Square-r1-r2....Etc any more

try reinstalling motioninjoy. Then go to drivers manager and remove all drivers from motion in joy that are installed. Then close mij and uninstall it. Then try to reinstall the software of scarlet.