11-07-2017, 09:56 PM
i recently began trying to use pcsx2, and while it seems to be able to run games (emulator and pc don't crash) it for some reason drops framerate severely at the actual gameplay portion itself, i tested on two games (COD big red one, and lego star wars) and for some reason except for a visual glitch fixed by F9 the game of cod runs smoothly at 60 fps until the actual game itself is entered (right after entering a new game) the beginning, cinematic, music, and actions all work fine until then, while in lego starwars, its pretty much the same idea except the frame rate for lego star wars is a bit more consistent at about 10-15 fps as apposed to Big red ones 3-6 fps.
i looked into fixing the frame rate through changing setting in the emulator itself, or even plugins, however, for some reason my version which is the most up to date version, has no plugins associated with it by default (i tried downloading some from the main pcsx2 website aswell) and most of the options have no ability to be changed at all, although most research shows that the things i cannot change shouldn't be changed anyway. when i tried changing the plugins with the ones i downloaded, half of them didnt work as it gives an error along the lines of "pc may be lacking resources" for one, and for another something similar to "open gl x version isnt supported/ isnt fond, open gl 0 found" and both result in the emulator not working, but if i use default setting (which resets back to absolutely no plugins at all) it opens stuff again but may partially be why it isnt working properly or allowing me to change things for better performance.
my pc is on the older side from around 2011 so i dont expect it to run 100% with no flaws and no frame drops sometimes, but it should be able to handle the games pretty well, i have many emulators for various consoles and of those the only one ive ever had similar issues with (except far worse than just frame rate issues) was dolphin which can actually get games running but is ultra stuttery and laggy from beginning to the time i end it, while pcsx2 seems to run stuff well as is the case with the afore mentioned cod, which plays the entire opening cutscene, plus all the menues and inputs perfectly at 60 fps before instantly dropping to just above 3-6 when the actual gameplay begins which with a game that old, it shouldnt have more issue than the reletively newer game lego starwars which stays at around 10-25 fps and basicly runs half speed.
i have attached the tech specs of the pc so those who understand tech specs better than i, might be able to let me know if it can in any way be fixed or if the pc itself is the reason it cannot run properly.
in regards to the plugins i tried downloading they arent counted as the default plugins for which pcsx2 apparently had none, but as im unsure what to use to make the emulator run at its absolute best with what i have, i try to keep it default, and unless im using direct3D9 or 11 it seems as though pcsx2 breaks entirely which is the only expected result
gsdx32-sse4 gives the error "the plugins reports that your hardware/software drivers are not supported".
if this goes somewhere else on the forums, i will move if possible but it seems to fit here.
i looked into fixing the frame rate through changing setting in the emulator itself, or even plugins, however, for some reason my version which is the most up to date version, has no plugins associated with it by default (i tried downloading some from the main pcsx2 website aswell) and most of the options have no ability to be changed at all, although most research shows that the things i cannot change shouldn't be changed anyway. when i tried changing the plugins with the ones i downloaded, half of them didnt work as it gives an error along the lines of "pc may be lacking resources" for one, and for another something similar to "open gl x version isnt supported/ isnt fond, open gl 0 found" and both result in the emulator not working, but if i use default setting (which resets back to absolutely no plugins at all) it opens stuff again but may partially be why it isnt working properly or allowing me to change things for better performance.
my pc is on the older side from around 2011 so i dont expect it to run 100% with no flaws and no frame drops sometimes, but it should be able to handle the games pretty well, i have many emulators for various consoles and of those the only one ive ever had similar issues with (except far worse than just frame rate issues) was dolphin which can actually get games running but is ultra stuttery and laggy from beginning to the time i end it, while pcsx2 seems to run stuff well as is the case with the afore mentioned cod, which plays the entire opening cutscene, plus all the menues and inputs perfectly at 60 fps before instantly dropping to just above 3-6 when the actual gameplay begins which with a game that old, it shouldnt have more issue than the reletively newer game lego starwars which stays at around 10-25 fps and basicly runs half speed.
i have attached the tech specs of the pc so those who understand tech specs better than i, might be able to let me know if it can in any way be fixed or if the pc itself is the reason it cannot run properly.
in regards to the plugins i tried downloading they arent counted as the default plugins for which pcsx2 apparently had none, but as im unsure what to use to make the emulator run at its absolute best with what i have, i try to keep it default, and unless im using direct3D9 or 11 it seems as though pcsx2 breaks entirely which is the only expected result
gsdx32-sse4 gives the error "the plugins reports that your hardware/software drivers are not supported".
if this goes somewhere else on the forums, i will move if possible but it seems to fit here.