..:: PCSX2 Forums ::..

(10-04-2013, 06:48 PM)miguel23and Wrote: [ -> ]Hi!, I'd like to use the integrated bluetooth.
hardware Ids:
USB\VID_413C&PID_8160
USB\VID_413C&PID_8160&REV_0173

can you add the hardware id for this?

I tried add the Id's to "BthWinUsb.inf" and update but it only worked the first time, then it didn't connect with my sixaxis.

Post #1530 y #1534 (pag 154) explained how to do the "BthWinUsb.inf" correctly, maybe it would help you.

---

(10-05-2013, 08:36 AM)xiaolinstyle Wrote: [ -> ]I installed this into the folder specified as administrator and I still can not get it to acknowledge that I have my ps3 controller plugged in via usb, even though its clearly showing in my devices, but as a 'playstation' controller.

have you check the "force install" option before click the "install" button? Sometimes you need to check that box in Windows 7 and 8 in order to install it properly.

(09-27-2013, 08:58 PM)existingdark Wrote: [ -> ]Perhaps this is an issue. SCP DS3 Service isn't showing up at all. :/

(09-28-2013, 06:14 PM)existingdark Wrote: [ -> ]My issue is that SCP DS3 Service just simply won't install onto my system as a Windows Service. I have no doubt that the drivers themselves are installed but without the service, I'd might as well have nothing.

(10-01-2013, 01:55 AM)Beep Beep Wrote: [ -> ]That's the thing, I don't see it at all. Hence I'm unable to "turn it on".

@existingdark @Beep Beep, maybe this can help you:

(10-05-2013, 01:47 PM)razvandoa Wrote: [ -> ]Also one thing I would like to add :even though you are the admin you have to Give full read/write access from folder proprieties to the folder from where you will install the drivers (and unblock the exe files since they are downloaded from internet) cause the installation wont create the service.

Hello. Thank you for this wonderful wrapper+driver+awesomething!!!

But I'm having a problem. I installed it following your guide (I'm using win7x64 on an Asus laptop with BTdongle integrated), and at first it works really well, even the wireless bluetooth driver. But then, after a while whitout actively using it (1~2 hours), the bluetooth just stops working, and in the monitor it shows "Host address: Error". And that's it. It will never work again unless I uninstall everything and reinstall it. I already tried stoping and starting the bluetooth services, the SCP service and rebooting, plugin and unplugin the usb, and nothing works. Until the time that it finally stops working, I can turn off and on the controller and it pairs ok.
Using the usb it still works, so it is a problem with the BT dongle.

The devices list and BT HD_ID before installing:






And the devices list after the installation and while the problem:


This is how it looks the monitor when its recently installed and working (Note: It will not work wireless for the first time unless I turn off the controller L1+L2+Ps while wired, then it pairs ok):







And the error in the monitor:


I've Attached the logs

Thank you!!! I hope you can give me some advice...

PD: Sorry for my poor english.

I'm using the driver with a Power A Pro Elite Wireless Controller and have been noticing an issue where moving the left joystick in a circle a couple of times, it disconnects from the dongle for a few seconds then reconnects. Also, The hexadecimal code near its battery status in the Monitor program keeps increasing.

Ive tried everything I can think of and it refuses to acknowledge that I have a controller plugged in. Different usb port, force install, uninstall, reinstall, restart(s), pulled my bluetooth dongle entirely, but it still shows my PS3 controller as having an error in the control panel and says it cant start this device. Even though the driver is the SCP driver.

Please, can anyone help with this?

(10-06-2013, 07:12 AM)xiaolinstyle Wrote: [ -> ]Ive tried everything I can think of and it refuses to acknowledge that I have a controller plugged in. Different usb port, force install, uninstall, reinstall, restart(s), pulled my bluetooth dongle entirely, but it still shows my PS3 controller as having an error in the control panel and says it cant start this device. Even though the driver is the SCP driver.

Please, can anyone help with this?

Maybe your ps3 controller isn't a genuine one, this tool works with original DS3 but not always with fake ones. Maybe you need to install xbox drivers or something, here are the requisites:
Requirements
1. Microsoft .NET 4.0
2. Visual C 2010 Runtime.
3. Latest DirectX Runtime.
4. Latest Xbox 360 Controller Drivers available.
5. Genuine Sony DualShock3 or SixAxis Controller(s).
6. Minimum of Bluetooth 2.0 + EDR Dongle (if using Bluetooth).
7. Administrator rights on your PC.
Besides this, I'm clueless.

(10-06-2013, 06:46 PM)Huesoman Wrote: [ -> ]Maybe your ps3 controller isn't a genuine one, this tool works with original DS3 but not always with fake ones. Maybe you need to install xbox drivers or something, here are the requisites:
Requirements
1. Microsoft .NET 4.0
2. Visual C 2010 Runtime.
3. Latest DirectX Runtime.
4. Latest Xbox 360 Controller Drivers available.
5. Genuine Sony DualShock3 or SixAxis Controller(s).
6. Minimum of Bluetooth 2.0 + EDR Dongle (if using Bluetooth).
7. Administrator rights on your PC.
Besides this, I'm clueless.

I have two they are identical; both Sony branded and labeled with a serial number so...if they are fakes then Gamestop is carrying damn good replicas. I have and have had everything on this your list for some time. I was using motioninjoy for a few months but uninstalled it because every time I plugged it in to the usb to charge it freaked out and I had to go through a uninstall reinstall process that was never consistent. I had read that this was supposed to be a better solution yet it doesn't seem to work at all...any help would be appreciated.

I found the problem, when I tried to sync the controller to my PS3 again; it refused, so I then reset the controller (via the tiny inset button on the bottom of the controller) and now I'm having no issues.

Apparently through my use of motioninjoy the controller's internal memory settings were messed with.

I have some suggestions for it and a question:

1. It should be re-made with the C+/C++ programming language (if possible).
2. An installer should be made that installs the required components if they're not already installed and then installs the driver and service.
3. Why is it continuously sending data via the Internet?

Does not work on Windows 8.1 x64

PCSX2 seems to crash when I open Controller Configuration Screen

SCPUser.exe crashes with 0xc0000142