..:: PCSX2 Forums ::..

Hey, worked for me before the command of ps3 in wirelessly pc and usb've formatted my pc using windows 8 and have a compatible adapter asus bt21 the case esque install everything as it comes in the manual and it works usb but bluetoth not I work, when entering the mac monitor goes out of control and reserved but no way to connect forgive my form but I'm speaking Spanish if someone could help by skype or have a look at happy and help me through teamviewer.

(11-05-2014, 06:49 PM)karasuhebi Wrote: [ -> ]Have you tried XPadder?

I gave it a try, but it doesn't seem to detect the Guide/PS button like the other buttons.

Is there any way to "unplug" and power off the PS3 controller? MotionJoy had the "disconnect" button which would power off the controller preventing it from turning on your PS3.

Does this have anything like that? If so, where?

Thanks!

Is there a possibility to add support for another famous DS2 USB Adapter?
Twin USB Gamepad
VID_0810&PID_0001

I think it's even the most famous PS2/PC USB Adapter.

Wish it could be supported really.

Thank you.

Hi all. I have a quick question about this plugin; I checked a bunch of other pages of this thread but couldn't find anyone with the exact same issue, nor any solution that has worked for me, but I apologize in advance if I simply missed it.

I have installed the wrapper per the instructions and installed the update the same way. The installer reported it was successful with the same four lines at the bottom (DS3 Device installed, etc.), and the SCP Monitor accepts commands from the controller (I am using a usb cable). However, nothing else is treating it as a controller. Here is a list of information that, from other posts I've read, may prove as some clues, hopefully:

Windows 7 64 bit
Devices and Printers page in Control Panel reports BOTH the PS3 controller, and the "Xbox 360 controller", and only the PS3 controller disappears when disconnected; the 360 icon stays.
Device Manager has the 360 drivers installed as their own thing (from screenshots of other posts, it seems to be correct).
The only sign of the PS3 controller/drivers in Device Manager is a "USB DS3 Device", listed under Universal Serial Bus Devices. This entry disappears when the controller is unplugged.
In the properties of the above DS3 device, the drivers say Scarlet.Crush Productions.
As mentioned, SCP Monitor shows the controller as having a MAC address, with charge-level reported as well, and the configuration mode picks up button inputs on the DS3.
And finally, the main symptom of the issue; when I right click on either the DS3 or 360 icon in "Devices and Printers", and then click "Game controller settings", it is just a blank list.

Also, I have never used nor even downloaded MotioninJoy, and have already tried doing multiple re-installs of SCP, uninstalling the PS3 device in Device Manager, etc. So, if anyone has any ideas on this, I would greatly appreciate it! I want to play Isaac so bad haha.

Either way, thank you all in advance!

Okay, so big fan of the Scarlet Drivers, have served me well for the longest. I even finally got my Bluetooth Driver to rcognize it wirelessly. It runs near flawlessly, and the ps3 outclasses my 360 controller and it's wireless adapter completely[especially with it's lack of the floating issue.]

Unfortunately, I have one very long standing issue with the drivers, and it comes with R3 presses. In the game Warframe, I use the D-pad for my skills/abilities. I have L3 as my sprint button. And left Analog as my movement. The problem is, when trying to use the left analog to move while attempting to sprint, I will initiate D-pad presses and activate skills prematurely.

When I got into controller properties and move the left analog about while pressing L3, I actually get a mess of lights. Quick flickers, but intups none the less. This has been my bane for many runs, and is the only reason I'll stick to my floaty Xbox controller for now.

Is there a fix to this issue, as it has been prevalent in every version of Scarlet I have used? I've also experienced this in a few MotionJoy versions I tried before finding SCP. Haven't gone back to MiJ, and don't plan on it.

Windows 8.1 64
Classic DS3 controller
Problem persists both through Bluetooth and wired

Any help would be greatly appreciated. Thank you in advance.

Weird. It sounds like your controller itself may have issues.

I recently build a new HTPC/Emulation box. I already own a playstation 3 and as such I had two DualShock 3 controllers already. I wanted to have four controllers total, so I purchased two DualShock 4's as I feel they're much better than DS3's, and not terrible more expensive.

Here's where my trouble begins though. With the DS4's I also bought a USB bluetooth dongle, so I could hopefully get rid of the cables. I've installed the SCP driver package and the DS4 update and got the controllers working as long as they're wired. I had all four controllers plugged in at the time I installed SCP.

The DS4's pair just fine with the bluetooth, but I can't get the DS3s to pair alongside them at all. Further, the range of the bluetooth dongle seems ridiculously low, and input gets dropped constantly. This is the dongle I bought: http://www.logilink.eu/showproduct/BT0015.htm[2] I have inputs being missed when sitting in my couch about 3 meters away from the box, and I've got the bluetooth dongle plugged into a USB port on the front. The problem seemed to get even worse when two controllers were connected, and I am completely stumped. As far as I know, the bluetooth dongle should be perfectly fine for that range, so that leaves a software problem.

I don't know if SCP is at fault here, and if it is I'm not sure how else to get my controllers connected. I really like the fact that they show up as as xbox controllers since that saves me a ton of headache in setting up inputs for ex. steam and xbmc.
Second issue is that I can't get the DS3s to work with bluetooth at all. I'm not sure if I missed some step in the installation or what the hell is going on. After the installation I simple unplugged the DS4s and pressed the PS button, and they were paired. No such luck with the DS3s. If it isn't possible to have both side by side, I'd be fine with the DS3s being wired.

Anyway, if anyone has some experience connecting both DS3's and DS4's via bluetooth, I'd love to hear from you. Oh, and if there's anything I can tell you about my setup that would be helpful in figuring this out, go ahead and ask. Thanks.

Hello, i love this i need this for fifa, it worked in a time when i had alot of bsods> which are video driver related and now solved.

I dont have bsod anymore, but when i try to run this for a few minutes my screen turns into a pause screen, i need to push the power button to shut the pc down.

Did i forget something to install ?

I followed a Youtube video tutorial showing a guy using your drivers and it worked like a charm even connecting through bluetooth without a dongle.
The one thing that I am curious about is the ScpPair tool. How does it pair DS3 to other devices exactly?
Let me be straight, before your amazing work I had no hope of connecting my DS3 to my laptop via bluetooth (Intel BT chip) and I thought that I need to buy a dongle. The point is they say all over the internet that you cannot pair a DS3 with a Windows Phone (8.1). So is it possible using this tool?