Hi there,
First make sure you have the .139 update applied, then run ScpMonitor.exe and right-click on the little icon in the taskbar and click Configuration, Disable SSP and see if that helps. You might have to restart the service or reboot after disabling SSP. SSP is a newer protocol for the DS4 gamepads, and has problems with some systems and DS3's, and disabling it seems to help in some cases.
best regards,
- dink
(02-19-2014, 03:17 PM)Sterne Wrote: [ -> ]Hello everyone. I have been using xinput wrapper for a long time now. I didnt have any problem with it for something like 2 years and now I seem to really struggle with it.
It installs just fine but it cant pair my bt dongle with ds3. In monitor it shows <error>. My dongle has this green blinking light - it just stops blinking when I install xinput wrapper drivers.
At first I thought that my bt dongle is just dead but I sent couple pictures from my phone using bluetooth. This dongle is on supported list and it was working just fine on previous windows install.
Can anyone please give me some hints? I made print screen with my current install.
http://image.bayimg.com/60913ce86d860ee4...e9585f.jpg
Now this is embarrassing... I didnt notice that there is an update from .136 to .139.
I didnt even had to turn off ssp and it paired without any problems. Thank you Dink!
Tried updating to 1.1.0.139 — no luck, BT connection doesn't work.
(02-18-2014, 08:24 PM)neo0031 Wrote: [ -> ]I've been using this Wrapper/installer for a while now and I have been preaching for people to stay away from the poison that is MIJ.
This ScarletCrush wrapper has been working great for me with no problems until recently, for which I am forever grateful.
However, I've recently encountered a problem where Windows 7 would disconnect and reconnect the controller in game whenever Rumble is activated outside a certain timeframe, and the OS would play the USB connect sound. I am not sure if this problem has been reported before.
I am using the latest update (even though problem has occurred in previous literations) with a DS3 controller via USB, on Win 7 64bit.
Maybe a reinstall is my solution, but I think I would need some pointers on how to go about doing that.
Thank you.
UPDATE: A reinstall did NOT fix the problem.
Sorry for self-bump, but any suggestions for this issue?
Dear,
To All.
A have Problem as my DS3 controller stated by 00:26:5c... mac address not pair, but other ds3 controller start with 78:18 mac is pair.
{my old DS3 controller is pair no any problem but my new DS3 controller is not pair}
Help me Please...
_________
Win7 64 Bit System
Manual install of DS4 driver from ZADIG.EXE results in BSOD. When trying to connect the controller, Windows update tries to DL a new driver for the device resulting in the crash.
Worked around it by not following the forum posts and skipping the manual install of the DS4 driver from ZADIG.EXE. All features in ScpMonitor and all functionality appear to be working flawlessly.
Everything is installed correctly and my very modest overclock is 100% stable.
AsusBT400/Win7-64
Scarlet.
Help me.
RE: XInput Wrapper for DS3 and Play.com USB Dual DS2 Controller
Dear,
To All.
A have Problem as my DS3 controller stated by 00:26:5c... mac address not pair, but other ds3 controller start with 78:18 mac is pair.
{my old DS3 controller is pair no any problem but my new DS3 controller is not pair}
Help me Please...
_________
Win7 64 Bit System
(01-18-2014, 01:04 PM)SleepMachine Wrote: [ -> ]Hi
Thanks for a great product.
I have used this driver successfully in the past. Bluetooth seemed to work pretty good, as far as i can remember. However, since then i have had a HDD chrash and needed to reinstall Win7 after getting a new hard drive.
However this time i'm having some problems playing over BTH. It works mostly fine, but every five minutes or so, the controller becomes non-responsive for a couple of seconds. After that, it starts to work again. Does this seem familiar to anyone?
All my hardware and software should be the same as last time. My dongle is an Asus USB-BT211 v2.1 + EDR.
Hi, I recently got an Asus USB-BT211 (USB\VID_0B05&PID_1783), and I've been having the same issues as the user I've quoted. At first, it would barely see my inputs on my controller, but now it just sometimes cuts out. I'm noticing it's happening a lot more in games where rumble is used, which I'm also not used to, since I've been using the XInput Wrapper with my two DS3 controllers wired perfectly, but I've never used rumble.
Hey all, sorry if I come across as an idiot, but i was using Motioninjoy and after hearing about how it could potentially be malicious, I looked for alternatives and found this. The thing is i have no clue how to get it to actually work now that i have installed it. Windows doesnt show anything in the "Setup USB controller" section and when i open up the emu i just cant get it to register. Also I am using a wired controller.
Nevermind got it working. I just uninstalled and reinstalled the driver again, oh and I guess it helped that i actually downloaded and installed the 360 controller driver, duh.
Hello I've just bought a new blue-tooth adapter "USB\VID_0A12&PID_0001". I've installed it according to instruction from post 1 and everything was ok:
-- Install Summary --
SCP DS3 Service
Bus Device
Bus Driver
DS3 USB Driver
Bluetooth Driver
But I cannot use my pad through blue-tooth...
I attached the ScpService.log