(02-23-2014, 09:02 PM)dielectric Wrote: [ -> ]Hello I've just bought a new blue-tooth adapter "USB\VID_0A12&PID_0001". I've installed it according to instruction from post 1 and everything was ok:
-- Install Summary --
SCP DS3 Service
Bus Device
Bus Driver
DS3 USB Driver
Bluetooth Driver
But I cannot use my pad through blue-tooth...
I attached the ScpService.log
I've got the same ID on my adapter and can't get it to work through bluetooth either. Just to verify that we have the same exact issue:
When connecting through bluetooth:
- Does the controller stop blinking after a while and only have one light lit?
- Does SCPMonitor show the controller as connected meaning it's not "reserved" anymore and it says "bluetooth" instead?
- If yes at the above, can you use the "SCPUser.exe" program to make it vibrate (click the "advanced" box and then pull the sliders)?
(02-24-2014, 12:37 AM)Zpirit Wrote: [ -> ]I've got the same ID on my adapter and can't get it to work through bluetooth either. Just to verify that we have the same exact issue:
When connecting through bluetooth:
- Does the controller stop blinking after a while and only have one light lit?
- Does SCPMonitor show the controller as connected meaning it's not "reserved" anymore and it says "bluetooth" instead?
- If yes at the above, can you use the "SCPUser.exe" program to make it vibrate (click the "advanced" box and then pull the sliders)?
about the one light, it's normal. Or at least it's alwais like that for me when i'm using the pad with bluetooth
(02-24-2014, 02:03 PM)ultimategrayfox Wrote: [ -> ]about the one light, it's normal. Or at least it's alwais like that for me when i'm using the pad with bluetooth
Yeah I know. It's because it's connected I guess but the strange thing is that no input is registered, I can make it rumble but pressing buttons doesn't do anything.
@Zpirit: your dongle doesn't support EDR.
Hey Everyone,
@Scarlet.Crush THANKS MAN !!! I have been using it for a while now and works great.!! I do have a few minor problems.
1. I bought some new controllers and they won't connect via BT. I found out that only true Sony controllers will work NP. Will just send those back
and get some of Sonys.
2. I have the service to start automaticly, but when I shut down the computher and restart it the service doesn't start.
Any ideas?
Thanks again...
Hobs
(02-24-2014, 06:50 PM)Scarlet.Crush Wrote: [ -> ]@Zpirit: your dongle doesn't support EDR.
I suspected something like that, thanks for confirming it. Will pick up a new one and hopefully it'll work
Anyone got any recommendations?
(02-23-2014, 09:02 PM)dielectric Wrote: [ -> ]Hello I've just bought a new blue-tooth adapter "USB\VID_0A12&PID_0001". I've installed it according to instruction from post 1 and everything was ok:
-- Install Summary --
SCP DS3 Service
Bus Device
Bus Driver
DS3 USB Driver
Bluetooth Driver
But I cannot use my pad through blue-tooth...
I attached the ScpService.log
Is your controller a true SONY product? I had the same issue and was using
sony knockoffs. THESE WILL NOT WORK.
Hobs
(02-24-2014, 07:25 PM)Hobs Wrote: [ -> ]2. I have the service to start automaticly, but when I shut down the computher and restart it the service doesn't start.
Any ideas?
Zip up your ScpService.log and post as an attachment.
(02-25-2014, 04:00 AM)Scarlet.Crush Wrote: [ -> ]Zip up your ScpService.log and post as an attachment.
I said that it doesn't run when I restart my computer. That is incorrect. It starts but the Host address is Disconnected.
THanks
Hobs
hi so, i installed everything and when i click scpuser it shows that the inputs are working properly...but my device manager shows a yellow question mark next to xbox 360 controller and nothing works in game.
any ideas?